Modify code for Arduino working with 2.8 tft touch screen.
€30-250 EUR
ปิดแล้ว
โพสต์ มากกว่า 5 ปีที่ผ่านมา
€30-250 EUR
ชำระเงินเมื่อส่งงาน
I wrote code for Arduino Mega and an UHF rfid reader module (VM-5GA) on seriel (pin 20 & 21) , and DS3231.
Work fine
I also wrote code for mega + totuch screen TFT 2.8. Work fine too.
But i never could let both working together (reader on serial + touch screen + DS3231)
It seems to be a conflict with pins used by touch screen.
I need somebody to correct the code to let me use touch scren with rfid reader on serial and ds3231.
hello,how are you. i read your bid carefully.
i am c/c++, arduino expert and have full experience for 10 years.
c/c++, arduino is my top skill and i can build your project by using c/c++, arduino.
i can provide most quality and high speed.
if you want to success, please contact me.
Then, I will give you good result to the proposals.
hire me.
Hello How are you? I am an embedded software and hardware engineer who has enough experience in embedded system and Arduino programming.
I have done similar projects that is to control TFT touch screen using Arduino mega via spi communication. I understand your problems and we can detect and figure out the problem if we discuss the project in detail.
Please contact me to discuss the project in detail.
Thank you
Alexander
Hi,
I hope you are doing well. I have experience with these TFT screen and RTC module.
I have understood your requirements and I can get it resolved.
Send me message for further discussion.
Looking Forward,
Khawaja
Dear sir
I have more than 10 years experience in embedded systems design , I can handle the arduino sketches and make it works, please message me so that we can discuss more details
Best regards
I have worked with Arduino MEGA and DS3231 as RTC module. I can solve the touch screen and RFID problem if you send me the RFID and Touch Screen hardware to my address. Have more than 15 years of experience on Digital Electronics.
Good day, Season's greetings. I have read the details of your project and I can help you fix this problem. I think you just have to use different CS pins to control them because they both use the SPI protocol. Please contact me so that we can work together on this.
Hi. I'm professional programmer/electronic hardware developer with experience over 20 years. I very well know Arduino platform and I can help you. I need to know TFT module model.
Regards, Alex.
Hi,
I have experience for 15+ years in electronics/embedded development. I have several years of advanced AVR/arduino development, including library development from scratch. Practically all Arduino AVR boards used, like: 2009, 2010, UNO, MEGA, NANO, MICRO, MINI, etc. Several shields used like Ethernet (W5100, ENC28J60, etc.) with various IP protocols implementation, various graphical TFTs with and without touchscreen and various BUS types (parallel, SPI, I2C, etc.), all kinds of sensors and buses, serial and parallel memories, etc.
I think I can easily fix your project by remapping the RFID reader pins as this seems to be a conflict with the RTC I2C pins. Also, You almost for sure are using a software serial implementation for the RFID reader, that is not as reliable as a direct hardware serial connection - I'll also change it to use HW serial interface for realliability.
If you are interested in my bid, feel free to contact me.
Regards,
Carlos.
May I take a look at your code?
I work with Arduino since 2010 and have more than 20 years of experience in programming and electronics. Also I have a huge experience in remote debug of Arduino-based devices
hello
i am a computer engineer,i have masters in computer engineering,i have experience
for more than 7 years in arduino and electronics
could u kindly send to me the code to be able to understand it,but initially it is doable
Hi,
Usually touch screen comes with I2C/SPI interface, while DS3231 use I2C interface. I guess you are correct, it's about pin/ peripheral conflict. let me help you solve it.
I have programing arduino since 2013 and I know how it works. I'm professional firmware engineer, So I know well how to programing embedded stuff like this. this is my daily activity.
Let me know your code and let's analyze it.
Best Regards,
Rijal
Hi, I'm an embedded software engineer with a lot of experience with Arduino development. I know how to fix the pin conflict between the display and other modules, so that they can all work together perfectly. I work fast and write tight efficient C/C++. Contact me to discuss details.
Hi,
Leme brief my capabilities first. I have worked extensively ESP32 for the past 8 months at my current company as a tech lead in design and development of a custom board based on it. The projects done on the same cater the need of satisfied clients in automotive, telematics and industrial applications . BT,WIFI,SD CARD,CAN ,SPI,I2C, AI,DI,DO,AO,UART etc were interfaced and tested throughout the process. IOT projects which communicates with client server via mqtt and http were also done on the same.
I have also worked on PIC,AVR,ARM,ST and much more chips and boards like arduino,Pi,nodemcu too.
Since i have worked on arduino before i have faced problems while using software serial and spi together and what i did was using I2C in place of serial.
We may have to try other options if needed.
Feel free to ask me anything regarding the same .
Thank you
Greetings!
I am an electronic engineer and having 3+ years of experience of working as embedded engineer.
I am well versed in Arduino Ide programming, sensor integration, raspberry pi all models, python, embedded c, processing ide.
I have Experience of Working on all models of arduino.
I've build self balancing robo with remote control, tricopter, 3d printer, finger print sensor based bike automation etc.
As I am new on freelancer so I would request you with all my kind heart please give me a chance I would provide you best service.
Money is not my concern I need to make a good profile because I am new on freelancer.
It will be sincerely pleasure to hear back you soon.
I am waiting for your positive response.
Thank you so much.
Best Regards
Saurabh
"Hi, Hope you are doing well! Thanks for sharing your project requirement with us. It will be our great pleasure to work on your project. I have checked your requirement, yes we can do it, because we already work on similar requirement in past. We have right skills to work on this assignment. . We will complete the work as per requirement
Also my team working on same project"
We have read out every thing about your project
kindly confirm"
I have successfully used 3.2 inch, 3.5 inch and 4 inch display on Mega. I can help you with that.
Relevant Skills and Experience
Arduino, Tft display, labview, serial