Bltouch smoothiewareงาน
...Clogging: The SX4 Uses HIEHA’s unique nozzle throat with a Teflon Tube and print heads, which are engineered to run smoothly and resist clogging. Fast Heating & Printing Speed: Dual power supply design allows for fast heating of print bed and hot end. Stable CreoXY structure allowing super high printing speeds of up to 150mm/s. Auto-Leveling & Excellent Adhesion: HIEHA-SX4 uses a genuine BLTouch for reliable and precise auto-leveling. Once the heated bed cools down, the print is easily removed by hand, without requiring scrapers or spatulas. product page on amazon
I need some to configure a delta printer smoothieware config file to work with the machine. It is for an Azteeg X5 GT board.
I need some to configure a delta printer smoothieware config file to work with the machine. It is for an Azteeg X5 GT board.
Our company is , we sell controllers for CNC machines that run the Open-Source Smoothieware firmware. We also contribute to the continued development of the firmware, and are participating in the elaboration of the version 2 of the board and firmware for the Smoothieware project. As part of this, the project is aiming to move from USB/MSD to USB/MTP ( the same way Android did a while back ). We need the following USB/MTP driver: to be ported from it's the original platform ( Teensy 3.5 ) to our firmware ( Smoothie v2, using LPCOpen and FreeRTOS): USB/MTP will be used to offer users access to files on the SD card ( using SDIO access, SDIO access to files is already implemented in our firmware ). Additionally
Configure 3d printer board MKS SBASE 1.3 with 3,5" MKS TFT35 screen, wifi and filament run out system. (,searchweb201602_3_10152_10151_10065_10344_10068_5722815_10342_10325_10343_10546_10340_5722915_10548_10341_5722615_10696_10084_10083_10618_10304_10307_10820_5722715_10843_10059_306_100031_10103_10624_10623_10622_5722515_10621_10620,searchweb201603_32,ppcSwitch_5&algo_expid=a6bade3b-7e37-4f4a-8351-db43e819ca8c-3&algo_pvid=a6bade3b-7e37-4f4a-8351-db43e819ca8c&transAbTest=ae803_1&priceBeautifyAB=0). As well as Makerbase power shortage detection:
Overview: Development of a control package for a stepper motor driven Laser Cutter. Software components required: Laser Printer Driver O...check and adjust settings at this stage also. Starting sends the appropriate commands to the laser control board – You can then Pause/Stop/Restart the job Machine configuration will need to be setup and hidden in the laser control software. Experience: Software developer is expected to provide some examples of relevant experience e.g. CNC/Gcode/Printer driver architecture/3D printer/Smoothieware etc At this stage control board/firmware is still flexible and may be dependent of programmer familiarity but is likely to be G-code based. If you feel you are suitable for this project please make contact for a more detail...
I'm building a 3d printer The machine is a corexy design using the MKS Sbase v1.3 smoothieware clone controller. I've everything working correctly except for the hotend temperature. The hotend does not reach the desired temperature, it is always way low. The hotend is a J-head V6 E3D Hotend 1.75mm/0.4mm Nozzle Bowden type. The thermistor is NTC3950. The system power 24v. In the file I've tried using the setting, the Steinhart Hart and the temperature_control.hotend.rt_curve setting. From experimenting with settings using a laser thermometer and ohm meter, the Steinhart Hart curve is very steep. I'm thinking I need to make a circuit give the Steinhart Hart more slope at higher temperatures but have no idea how
We have a almost fully functioning 2 arm Scara utilizing smoothieware firmware. It needs to be fine-tuned as there are some small problems with speed consistency. Also homing configuration needs to be accomplished.
We have a almost fully functioning 2 arm Scara utilizing smoothieware firmware. It needs to be fine-tuned as there are some small problems with speed consistency. Also homing configuration needs to be accomplished.
